Mini Scrap Wood Scarecrow

You will need:

*Piece of scrap wood-I used a small piece of a 2×4

*Burlap

*Jute twine

*Paint-whichever colors you prefer

*Paintbrushes

*Glue Gun-Here’s my affiliate link for the cordless glue gun I use.

The first thing I did was wrap my burlap around the top half of my board for the hat. I did fold the bottom inch or so over to make a brim for the hat.

Once I had the hat glued on I took a piece of jute twine and tied a little bow on the top of the hat to bunch it together.

Now, it’s time for the paint! I like to use smaller paint brushes for this. I started with the eyes and worked my way down the face. I used a round spouncer for the rosy cheeks but if you don’t have one you can certainly just use a paint brush to make them.

Once I had my face painted on, I then made a little raffia bow to stick on the brim of the hat.

No Sew Candy Corn Pillow Décor

Supplies needed:

*Waverly fat quarter fabric (Wal-Mart)

*Poly-fil

*Hot glue gun-click here for my affiliate link to the cordless glue gun I use

*Scisscors

*Raffia and ribbon-optional

The first thing I did was round up some yellow, orange, and white fabric. I found these fat quarters of fabric at Wal-Mart but you can find them anywhere that sells fabric or craft supplies. I had the poly-fil on hand but you can also find this at any store that sells craft/sewing items.

Next I took my yellow fabric and folded it in half. I then took my scissors and cut the base shape that I wanted for my candy corn. You want to make sure you have some good, sharp fabric scissors for this project.

Next, I did the same thing with my orange fabric.

Once you have your fabric cut to the correct shape you want to cut through the bottom fold as shown above. Repeat the same step with the white fabric. Don’t forget to cut through the bottom fold on the white fabric as well.

Now, it’s time to start gluing the candy corn together! Yep that’s right…it’s a no sew pillow! I first started by gluing together the sides of the yellow fabric, leaving the top open for stuffing. Next, I lined up the orange fabric to where it needed to be and then folded the bottom edge under for a more finished look and glued that down. I repeated the same step to the back of the candy corn. Remember to leave the middle seams of the front and back of the candy corn open for stuffing.

Next, you will do the same thing to the white fabric. Don’t panic if your fabric doesn’t line up perfectly as you can go back and trim it once you get your candy corn glued together. Make sure and leave the top of the white fabric open so you can put the stuffing in.

Now it’s time to stuff the candy corn. I like to use a wooden stick or dowel to help push the stuffing through. Once you have it as full as you would like then you an glue shut the top of the candy corn.

Once I had my candy corn all glued together I went around and trimmed up where I needed to and round the top a bit. It needed a little something more so I tied some raffia around the middle.

It looks adorable just like this but of course I had to add a bow to mine! I just used a few different patterns of ribbon and crisscrossed my pieces to make a quick and easy bow.

DIY Scrap Wood Scarecrow

You all know I love me some scrap wood projects and I am really excited to share this one with you!

Supplies Used:
*6- 2 1/2 x 40 Inch boards for the body
* 1- 2 1/2 x 26 1/2 for the brim of the hat
*2 1/2 Inch Screws
*1 3/4 Inch Screws
*Drill
*Stake and supports(optional) we used 1/2 in. x 1 in. boards
*Sanding Block(optional to add distressing if desired)

To start off we used saw horses to lay all of our boards on. We laid the board we were using for the brim of the hat across the underneath of the longer boards. You will want to lay all of the backs of your boards facing up when your screwing on the brim of the hat. Once you have your boards how you want them your ready to put the screws in. We used the 2 1/2 Inch screws for this step.

Next we took some smaller pieces of scrap wood we had laying around to make a support for the bottom and added some stakes so we could stick the scarecrow in the ground. Where we live the wind is never ending so in order to have anything not blowing away or tipping over we have to make sure it’s staked down.

We did pre-drill these before putting the screws in to avoid the wood splitting. We used the 1 3/4 Inch screws for this step. Our stakes were 14 inches long and we just cut the point in the ends with a miter saw. Once we had our stakes screwed on we added a 1 inch x 12 3/4 board in between the two for extra support. We also pre-drilled these holes as well. These steps are optional obviously if you didn’t want to stake your scarecrow into the ground.

Now that you have your stakes and support screwed on it’s time to start painting and designing your scarecrow. There are so many different ways to design scarecrows so i’m not going to do that step by step as it’s fun to add your own spin on these kinds of projects.

Here are a few pictures of my scarecrow while I was dressing it up!

I painted my hat and brim and then once dried i used my sanding block to add some distressing.

Next it was time for the face! There are TONS of different ways to paint a scarecrow face so I just did a combination of several different ones that i have seen.

I added some polka dots to his hat and used my Chalk Couture supplies to write “WELCOME” on the brim of the hat. I also added some raffia for the hair. You know I always have to add a bow to my projects so I just used some mustard colored burlap, polka dot burlap and some raffia and made a super easy and cute bow to finish off my scarecrow. Once I was all finished I did spray my scarecrow with a clear coat to seal it.

I absolutely love how this turned out so I also made a mini version to sit on my deck! What do you think? Stinkin’ cute, right?

Scrap Wood Pumpkins

Supplies:

*Scrap Wood

*Apple Barrel Paint-I used Harvest Orange and White

*Cinnamon Sticks

*Raffia-I used natural and orange colored from the Dollar Tree

*Sanding Block or Sand Paper

*Hot Glue Gun-Amazon affiliate link

*Painter’s Tape

*Paint Brush

*Spouncer-optional

The first step is to paint your pumpkins. I chose “Harvest Orange” Apple Barrel paint for my base color. Once that dried I took my sanding block and distressed my wood a bit.

Next I took my spouncer and added white polka dots to my small pumpkin. If you don’t have a spouncer you can certainly just free hand your dots.

While my small pumpkin dried I took my painter’s tape and taped off my stripes on my big pumpkin and then painted those white as well.

Once the paint dried i peeled off the tape. I then took my sanding block and distressed the pumpkins a little more until I got my desired look.

Next for the stem of the pumpkins I took a cinnamon stick and broke it in half and used half for each pumpkin, securing with hot glue. Not only does this look super cute but it also smells good!

Now, these are adorable just like this but to dress them up even more I decided to add a bow to mine. Shocker, right? HaHa

I simply took a few smaller pieces of burlap ribbon and raffia and tied up a cute little bow.

Hello Fall Door Hanger

Supplies:

*Wooden pumpkin hanger-Hobby Lobby

*Wooden “Hello Fall” hanger-Hobby Lobby

*White paint-I used Apple Barrel but any kind will do.

*Orange paint-I used Waverly chalk paint from Wal-Mart.

*Mini Buffalo Plaid Transfer-Chalk Couture.

*Eucalyptus Chalkology Paste-Chalk Couture

*Squeegee-Chalk Couture

*Foam brush

*Ribbon and Raffia-optional

*Wood Beads-affiliate link

I did a live video on this door hanger but thought it turned out too cute not to put on the blog so here it is. I love how this turned out and you could certainly put your own twist on it to make it your style.

I chose to add a bow to my hanger because if you know me, you know I put bows on darn near everything…HaHa! I love the farmhouse look that the wood beads added to it. What do you all think?